IGate - Revision history

Ian: /* Configuring TNC */

2014-06-05T05:58:13Z

Configuring TNC

← Older revision		Revision as of 05:58, 5 June 2014
Line 171:		Line 171:
	$ minicom -s		$ minicom -s
	<pick 'serial port setup'>		<pick 'serial port setup'>
	<change serial device to '/dev/~~ttyACM0~~'>		<change serial device to '/dev/ttyUSB0'>
	<set BPS to '4800 8N1'>		<set BPS to '4800 8N1'>
	<set Hardware flow control to 'no'>		<set Hardware flow control to 'no'>

2014-04-15T04:40:52Z

Installing APRX

2014-04-15T04:40:30Z

Configuring TNC

← Older revision		Revision as of 04:40, 15 April 2014
Line 172:		Line 172:
	<pick 'serial port setup'>		<pick 'serial port setup'>
	<change serial device to '/dev/ttyACM0'>		<change serial device to '/dev/ttyACM0'>
	<set BPS to '~~115200~~ 8N1'>		<set BPS to '4800 8N1'>
	<set Hardware flow control to 'no'>		<set Hardware flow control to 'no'>
	<Select 'exit'>		<Select 'exit'>
	<hit enter a few times to get cmd prompt>		<hit enter a few times to get cmd prompt>
	cmd:~~usbkiss on~~		cmd:amode kiss
	<ctrl-A>ZQ<enter>		<ctrl-A>ZQ<enter>
	</pre>		</pre>

2014-04-15T04:39:20Z

Installing APRX

2014-03-30T17:16:29Z

← Older revision		Revision as of 17:16, 30 March 2014
Line 122:		Line 122:

	<interface>		<interface>
	serial-device /dev/~~modem~~ 115200 8n1 KISS		serial-device /dev/ACM0 115200 8n1 KISS
	tx-ok true		tx-ok true
	</interface>		</interface>
Line 169:		Line 169:
	<pre>		<pre>
	$ sudo apt-get install minicom		$ sudo apt-get install minicom
	$ ~~sudo ln~~ -s /dev/ttyACM0 ~~/dev/modem~~		$ minicom -s
	~~$ minicom~~		<pick 'serial port setup'>
			<change serial device to '/dev/ttyACM0'>
			<set BPS to '115200 8N1'>
			<set Hardware flow control to 'no'>
			<Select 'exit'>
	<hit enter a few times to get cmd prompt>		<hit enter a few times to get cmd prompt>
	cmd:usbkiss on		cmd:usbkiss on
	<ctrl-A>ZQ<enter>		<ctrl-A>ZQ<enter>
	</pre>		</pre>

2014-03-28T20:46:14Z

SSH Tunnel for Remote Administration

← Older revision		Revision as of 20:46, 28 March 2014
Line 42:		Line 42:
	= SSH Tunnel for Remote Administration =		= SSH Tunnel for Remote Administration =
	If your iGate is going to be living behind a firewall and not have a fixed IP address, creating an SSH tunnel back to a central machine is a great way to make an always-on connection to connect to your Pi in the field. This configuration will set up a tunnel whenever the Pi is booted, and it will restart the tunnel if it ever quits for any reason.		If your iGate is going to be living behind a firewall and not have a fixed IP address, creating an SSH tunnel back to a central machine is a great way to make an always-on connection to connect to your Pi in the field. This configuration will set up a tunnel whenever the Pi is booted, and it will restart the tunnel if it ever quits for any reason.

			Set up ssh client to drop the connection after 120 seconds if no response from server. Add the following line to /etc/ssh/ssh_config:
			<pre>
			ServerAliveInterval 120
			</pre>
			Generate a key pair allowing connection to the server without requiring a password.
	<pre>		<pre>
	$ mkdir ~/.ssh		$ mkdir ~/.ssh
Line 85:		Line 91:
	[gateway]$ ssh -l pi -p 2222 localhost		[gateway]$ ssh -l pi -p 2222 localhost
	</pre>		</pre>

	= Installing APRX =		= Installing APRX =
	<pre>		<pre>

2014-03-25T04:46:40Z

Installing APRX

← Older revision		Revision as of 04:46, 25 March 2014
Line 152:		Line 152:
	compress		compress
	}		}
			</pre>

			Add the following line to /etc/rc.local:
			<pre>
			/sbin/aprx -L
	</pre>		</pre>

2014-03-25T04:45:21Z

Installing APRX

← Older revision		Revision as of 04:45, 25 March 2014
Line 139:		Line 139:
	</source>		</source>
	</digipeater>		</digipeater>
			</pre>
			Create the file /etc/logrotate.d/aprx:
			<pre>
			/var/log/aprx/aprx.log
			/var/log/aprx/aprx-rf.log
			{
			rotate 7
			daily
			missingok
			notifempty
			delaycompress
			compress
			}
	</pre>		</pre>

	== Configuring TNC ==		= Configuring TNC =
	<pre>		<pre>
	$ sudo apt-get install minicom		$ sudo apt-get install minicom

2014-03-25T04:35:48Z

Installing APRX

← Older revision		Revision as of 04:35, 25 March 2014
Line 115:		Line 115:

	<interface>		<interface>
	serial-device /dev/modem ~~19200~~ 8n1 KISS		serial-device /dev/modem 115200 8n1 KISS
	tx-ok true		tx-ok true
	</interface>		</interface>
Line 128:		Line 128:
	<source>		<source>
	source $mycall		source $mycall
			relay-type digipeated
			viscous-delay 0
			ratelimit 60 120
	</source>		</source>
	<source>		<source>
	source APRSIS		source APRSIS
	relay-type third-party		relay-type third-party
			viscous-delay 5
			ratelimit 60 120
	</source>		</source>
	</digipeater>		</digipeater>

2014-03-25T04:29:45Z

Configuring TNC

← Older revision		Revision as of 04:29, 25 March 2014
Line 143:		Line 143:
	<hit enter a few times to get cmd prompt>		<hit enter a few times to get cmd prompt>
	cmd:usbkiss on		cmd:usbkiss on
	<ctrl-A>~~<ctrl-Z>Q~~<enter>		<ctrl-A>ZQ<enter>
	</pre>		</pre>