Sector Radio Configuration - Revision history

Va7stv at 16:36, 5 July 2020

2020-07-05T16:36:54Z

← Older revision		Revision as of 16:36, 5 July 2020
Line 82:		Line 82:
	##* Configure the modem/radios ip address in the local subnet		##* Configure the modem/radios ip address in the local subnet
	##:<pre>/ip address add address={RADIO IP}/26 comment="Local Subnet" interface=BR-HW-OSPF network={RADIO NETWORK}</pre>		##:<pre>/ip address add address={RADIO IP}/26 comment="Local Subnet" interface=BR-HW-OSPF network={RADIO NETWORK}</pre>
			##:<pre>/ip route add distance=1 gateway={SITE GATEWAY}</pre>
	##* Configure DNS servers		##* Configure DNS servers
	##:<pre>/ip dns servers=44.135.216.2,44.135.216.3</pre>		##:<pre>/ip dns servers=44.135.216.2,44.135.216.3</pre>

Va7stv: /* Configuration Steps */

2020-07-05T16:33:32Z

Configuration Steps

← Older revision		Revision as of 16:33, 5 July 2020
Line 85:		Line 85:
	##:<pre>/ip dns servers=44.135.216.2,44.135.216.3</pre>		##:<pre>/ip dns servers=44.135.216.2,44.135.216.3</pre>
	##* Disable unused services		##* Disable unused services
	##:<pre>/ip service set telnet disabled=yes<pre>		##:<pre>/ip service set telnet disabled=yes</pre>
	##:<pre>/ip service set ftp disabled=yes<pre>		##:<pre>/ip service set ftp disabled=yes</pre>
	##:<pre>/ip service set www disabled=yes<pre>		##:<pre>/ip service set www disabled=yes</pre>
	##:<pre>/ip service set api disabled=yes<pre>		##:<pre>/ip service set api disabled=yes</pre>
	##:<pre>/ip service set api-ssl disabled=yes<pre>		##:<pre>/ip service set api-ssl disabled=yes</pre>
	##* Allow unencrypted SSH		##* Allow unencrypted SSH
	##:<pre>/ip ssh set allow-none-crypto=yes forwarding-enabled=remote<pre>		##:<pre>/ip ssh set allow-none-crypto=yes forwarding-enabled=remote</pre>

Va7stv: /* Configuration Steps */

2020-07-05T16:32:37Z

Configuration Steps

@@ Line 71: / Line 71: @@
 ## Wireless
 ##* Configure Interface (Frequency will depend on sector, as will radio-name)
-##:<pre>/interface wireless set [ find default-name=wlan1 ] band=5ghz-onlyn channel-width=10mhz country=no_country_set disabled=no frequency=5920 frequency-mode=superchannel mode=ap-bridge nv2-cell-radius=100 radio-name=VA7DIG/KUI0 rx-chains=0,1 ssid=HamWAN tdma-period-size=4 tx-chains=0,1 wireless-protocol=nv2</pre>/n
+##:<pre>/interface wireless set [ find default-name=wlan1 ] band=5ghz-onlyn channel-width=10mhz country=no_country_set disabled=no frequency=5920 frequency-mode=superchannel mode=ap-bridge nv2-cell-radius=100 radio-name=VA7DIG/KUI0 rx-chains=0,1 ssid=HamWAN tdma-period-size=4 tx-chains=0,1 wireless-protocol=nv2</pre>
 ##* Add our channels
 ##:<pre>/interface wireless channels add band=5ghz-onlyn comment="Cell sites radiate this at 0 degrees (north)" frequency=5920 list=HamWAN name=Sector1-5 width=5</pre>
@@ Line 79: / Line 79: @@
 ##:<pre>/interface wireless channels add band=5ghz-onlyn comment="Cell sites radiate this at 120 degrees (south-east)" frequency=5900 list=HamWAN name=Sector2-10 width=10</pre>
 ##:<pre>/interface wireless channels add band=5ghz-onlyn comment="Cell sites radiate this at 240 degrees (south-west)" frequency=5880 list=HamWAN name=Sector3-10 width=10</pre>

Va7stv: /* Before You Start */

2020-07-05T16:25:18Z

Before You Start

← Older revision		Revision as of 16:25, 5 July 2020
Line 2:		Line 2:

	== Before You Start ==		== Before You Start ==
			* It can be a good idea to build out your configuration in a text editor before you actually start to configure the radio. Once you are confident that it is correct you can start pasting it into the terminal one section at a time.
	=== Gather the information you will need:===		=== Gather the information you will need:===
	* Site VLAN ID		* Site VLAN ID

Va7stv: /* Configuration Steps */

2020-07-05T16:22:01Z

Configuration Steps

← Older revision		Revision as of 16:22, 5 July 2020
Line 1:		Line 1:
	{{Template:Alert \| type = danger\| message = Incomplete needs LOTS of work. }}		{{Template:Alert \| type = danger\| message = Incomplete needs LOTS of work. }}

			== Before You Start ==
			=== Gather the information you will need:===
			* Site VLAN ID
			* IP Address for this Sector
			* Site Subnet
			* Site Default Gateway
			* Radio Name
			* Radio Azimuth (0,120,240)
			* Radio Frequency
			* Radio Channel Width (Usually 10mhz)

	==Configuration Steps==		==Configuration Steps==

Va7stv: /* Configuration Steps */

2020-07-05T16:19:42Z

Configuration Steps

← Older revision		Revision as of 16:19, 5 July 2020
Line 42:		Line 42:
	#:<pre>/ip cloud set update-time=no</pre>		#:<pre>/ip cloud set update-time=no</pre>
	#:<pre>/system ntp client set enabled=yes primary-ntp=208.73.56.29 secondary-ntp=45.76.244.193</pre>		#:<pre>/system ntp client set enabled=yes primary-ntp=208.73.56.29 secondary-ntp=45.76.244.193</pre>
	# Clear the firewall rules		# Clear the firewall rules and add ours
	#:<pre>/ip firewall filter remove [find dynamic=no]</pre>		#:<pre>/ip firewall filter remove [find dynamic=no]</pre>
			#:<pre>/ip firewall filter add action=accept chain=input connection-state=established</pre>
			#:<pre>/ip firewall filter add action=reject chain=input dst-address=44.135.216.0/23 protocol=!icmp reject-with=icmp-network-unreachable src-address=!44.0.0.0/8</pre>
			#:<pre>/ip firewall filter add action=reject chain=input dst-address=44.135.160.0/21 protocol=!icmp reject-with=icmp-network-unreachable src-address=!44.0.0.0/8</pre>

	# Configure Networking		# Configure Networking
	## Interfaces		## Interfaces
Line 55:		Line 59:
	## Wireless		## Wireless
	##* Configure Interface (Frequency will depend on sector, as will radio-name)		##* Configure Interface (Frequency will depend on sector, as will radio-name)
	##:<pre>/interface wireless set [ find default-name=wlan1 ] band=5ghz-onlyn channel-width=10mhz country=no_country_set disabled=no frequency=5920 frequency-mode=superchannel mode=ap-bridge nv2-cell-radius=100 radio-name=VA7DIG/KUI0 rx-chains=0,1 ssid=HamWAN tdma-period-size=4 tx-chains=0,1 wireless-protocol=nv2</pre>		##:<pre>/interface wireless set [ find default-name=wlan1 ] band=5ghz-onlyn channel-width=10mhz country=no_country_set disabled=no frequency=5920 frequency-mode=superchannel mode=ap-bridge nv2-cell-radius=100 radio-name=VA7DIG/KUI0 rx-chains=0,1 ssid=HamWAN tdma-period-size=4 tx-chains=0,1 wireless-protocol=nv2</pre>/n

	##* Add our channels		##* Add our channels
	##:<pre>/interface wireless channels add band=5ghz-onlyn comment="Cell sites radiate this at 0 degrees (north)" frequency=5920 list=HamWAN name=Sector1-5 width=5</pre>		##:<pre>/interface wireless channels add band=5ghz-onlyn comment="Cell sites radiate this at 0 degrees (north)" frequency=5920 list=HamWAN name=Sector1-5 width=5</pre>

Va7stv: /* Configuration Steps */

2020-07-05T16:16:45Z

Configuration Steps

← Older revision		Revision as of 16:16, 5 July 2020
Line 44:		Line 44:
	# Clear the firewall rules		# Clear the firewall rules
	#:<pre>/ip firewall filter remove [find dynamic=no]</pre>		#:<pre>/ip firewall filter remove [find dynamic=no]</pre>
			# Configure Networking
			## Interfaces
			##* Create a bridge
			##:<pre>/interface bridge add name=BR-HW-OSPF</pre>
			##* Create the vlan back to the router (VLAN ID is site dependant)
			##:<pre>/interface vlan add interface ether1 name=ETH1-OSPF vlan-id=614</pre>
			##* Configure bridge ports
			##:<pre>/interface bridge port add bridge=BR-HW-OSPF interface=wlan1</pre>
			##:<pre>/interface bridge port add bridge=BR-HW-OSPF interface=ETH1-OSPF</pre>
			## Wireless
			##* Configure Interface (Frequency will depend on sector, as will radio-name)
			##:<pre>/interface wireless set [ find default-name=wlan1 ] band=5ghz-onlyn channel-width=10mhz country=no_country_set disabled=no frequency=5920 frequency-mode=superchannel mode=ap-bridge nv2-cell-radius=100 radio-name=VA7DIG/KUI0 rx-chains=0,1 ssid=HamWAN tdma-period-size=4 tx-chains=0,1 wireless-protocol=nv2</pre>

			##* Add our channels
			##:<pre>/interface wireless channels add band=5ghz-onlyn comment="Cell sites radiate this at 0 degrees (north)" frequency=5920 list=HamWAN name=Sector1-5 width=5</pre>
			##:<pre>/interface wireless channels add band=5ghz-onlyn comment="Cell sites radiate this at 120 degrees (south-east)" frequency=5900 list=HamWAN name=Sector2-5 width=5</pre>
			##:<pre>/interface wireless channels add band=5ghz-onlyn comment="Cell sites radiate this at 240 degrees (south-west)" frequency=5880 list=HamWAN name=Sector3-5 width=5</pre>
			##:<pre>/interface wireless channels add band=5ghz-onlyn comment="Cell sites radiate this at 0 degrees (north)" frequency=5920 list=HamWAN name=Sector1-10 width=10</pre>
			##:<pre>/interface wireless channels add band=5ghz-onlyn comment="Cell sites radiate this at 120 degrees (south-east)" frequency=5900 list=HamWAN name=Sector2-10 width=10</pre>
			##:<pre>/interface wireless channels add band=5ghz-onlyn comment="Cell sites radiate this at 240 degrees (south-west)" frequency=5880 list=HamWAN name=Sector3-10 width=10</pre>

Va7stv at 15:57, 5 July 2020

2020-07-05T15:57:51Z

← Older revision		Revision as of 15:57, 5 July 2020
Line 1:		Line 1:
	{{Template:Alert \| type = ~~warning~~\| message = Incomplete needs LOTS of work. }}		{{Template:Alert \| type = danger\| message = Incomplete needs LOTS of work. }}

	==Configuration Steps==		==Configuration Steps==

Va7stv at 15:57, 5 July 2020

2020-07-05T15:57:43Z

← Older revision		Revision as of 15:57, 5 July 2020
Line 1:		Line 1:
			{{Template:Alert \| type = warning\| message = Incomplete needs LOTS of work. }}

	==Configuration Steps==		==Configuration Steps==
	{{Template:Alert \| type = info\| message = When programming this radio for the first time it is generally easier to use the Mac Address of the device to connect to it from winbox, This will ensure that if you remove the current IP address you remain connected to the radio. You can do this by either typing the mac address into the address field or selecting a detected radio by clicking on the mac address column. }}		{{Template:Alert \| type = info\| message = When programming this radio for the first time it is generally easier to use the Mac Address of the device to connect to it from winbox, This will ensure that if you remove the current IP address you remain connected to the radio. You can do this by either typing the mac address into the address field or selecting a detected radio by clicking on the mac address column. }}

Va7stv: /* Configuration Steps */

2020-07-05T15:57:12Z

Configuration Steps

← Older revision		Revision as of 15:57, 5 July 2020
Line 33:		Line 33:
	#:<pre>/radius add address=44.135.217.99 secret=AmprNET service=login</pre>		#:<pre>/radius add address=44.135.217.99 secret=AmprNET service=login</pre>
	#:<pre>/user aaa set use-radius=yes</pre>		#:<pre>/user aaa set use-radius=yes</pre>
			# Configure SNMP Monitoring
			#:<pre>/snmp set enabled=yes contact="#HamWAN on irc.freenode.org"</pre>
			#:<pre>/snmp community set name=hamwan addresses=44.135.216.0/23 read-access=yes write-access=no numbers=0</pre>
			# Setup NTP
			#:<pre>/system clock set time-zone-name=America/Vancouver</pre>
			#:<pre>/ip cloud set update-time=no</pre>
			#:<pre>/system ntp client set enabled=yes primary-ntp=208.73.56.29 secondary-ntp=45.76.244.193</pre>
			# Clear the firewall rules
			#:<pre>/ip firewall filter remove [find dynamic=no]</pre>